Using your SMS007 global asset tracker.
Charging your unit:
Place the charger connector into the tracker, this will automatically power
up the tracking unit, its best to turn off the tracker to charge the tracker
correctly.
Turning your tracker on & off:
Hold the button in and wait for the led green light to flash fast, once this
happens press the same button three times very quickly, this will turn off the
tracker (No green light on)
charge for 3 hours, this should give the battery a full charge, you will see
the battery level on screen once your tracker updates.
Turning on the tracker:
holding the green button down, you will see the green led come on and the unit
will begin starting, this is usually apparent by the green light permanently
on this normaly will stal illuminated for 10-15 seconds (the green light will
start to flash as soon as the unit is ready)
Locating your tracking unit (POLL)
To locate your tracker or see where it is, simply click the poll button at the
bottom of your mapping screen and select an option example: (Locatenow)
Enter your password, usually the default password is the numeric value of 0000
then click send, your tracker is now updated to the option you have selected.
You can also select an auto track interval, the unit will send 255 tracks before
it will need to have the auto command re sent again. (This is to protect your
sim card credit)
Shockmode3:
If you POLL your tracker this command you will render the unit into a special
movement alert mode. When the unit/vehicle is knocked it will wake up and send
a tracking command to the server & activate the tracking system setting
it to report every two minuets provided the movement continues. It will then
move to track every two minuets until it the unit stops moving for more then
2 minutes.
Once movement is stopped the unit will stop sending reports, at which point
it will return to sleep mode again. This is a very good mode for using the unit
as a motorcycle alarm or car alarm, also as a trigger for just about any asset
that should not be moving anywhere. (This event works three times then needs
to be re set by POLLING the unit the command again) Try experimenting with this
mode, you can turn it on by POLLing it and then turn it off by POLLing resetunit.
IMPORTANT: when you use the command setshock3
you should also send an sms to your trackers phone number from your mobile phone,
in the text message you will send the following: ADDPHONE*123456*B*yournumberhere
make sure their are no spaces or full stops, send exactly what's shown above
in red taking care to also make sure you have caps lock on in the right places.
Once you send the command to your trackers phone number, your personal mobile
number will be pre set into the tracker ready.
On a shock event you will receive an alert to your mobile as well as your tracker
updating the mapping in your account. this function is very desirable for people
who want to use the tracker as a car alarm or asset trigger. This setting is
self cancelling after there has been 3 triggers, you can also cancel the setting
by POLLing the command through the web site 'resettracker' if you preset your
mobile number for alarms then each time there is an event you will be charged
for two sms messages as one will goto our server for the mapping and one will
goto your personal mobile phone as a alert.
Setting auto track eg: rptEvery30sec:
This function will allow the tracker to send reports to the server every 30
seconds.
Respectively the other rptEveryxxsec will set the tracking unit to automatically
report to the relevant time intervals.
LocateNow:
This is the most common setting that most people use, By POLLING this command
to your tracker it will relay its position to your mapping page where the location
will be saved for you online in your personal account.
In this mode the unit should run for and stand by for up to 15 days on once
charge, its important to note the more frequently you activate the GPS function
for tracking, the faster the battery will run down as GPS uses a lot of power.
In Locate now mode the trackers GPS is switched off by default, so make sure
you allow one to two minuets for you mapping to update once you send the command,
this is because as soon as your tracking unit receives the locatenow command
it will turn on its GPS to find its position before reporting its position to
you, this can some times take one minuet or so.
When using locate now, POLL once and if required POLL again, then wait refreshing
your screen, you location will update!
Their is not need to POLL the command more then Once.
GEO Fence:
To set a geo fence click the geo fence button and follow the on screen instructions,
you can send alerts direct to your mobile phone or e-mail.
The unit is a totally self contained tracking system which
will be connected to our server as soon as you purchase it.
Standby time could be up to 16 days (Subjective to track time) (Pay as you go)
The Mini track has 50 POLLs allocated to it from the time you purchase it, you can check your polls by clicking the POLL button you will then see your number of POLLs in the pop up box.
To purchase POLLs click buy polls in the tracking consult
& follow the instructions.
Your tracker will be sent out to you online with £5 credit on the internal
sim card normally T-mobile.
Do not change the sim card in your tracker as this will stop you unit from working
and may damage the tracking unit.
Do not open the sim card slot in your tracker as this is a waterproof seal and
should be checked to make sure it is seated properly in the slot of the tracking
unit.
Their is also a power point connection with a waterproof
connector located in the whole, this should be pushed into the power point charging
whole when ever the unit is not on charge.
Use any sim card - T-MOBILE IS RECOMENDED!